The tariff classification of a hydraulic power unit from Canada
No revocation or modification of this ruling appears in the Customs Bulletin issues read here (Nov 6, 2024 through Nov 18, 2026), where CBP publishes most such actions. That is not confirmation that the ruling is still in effect. Confirm its status with CBP before relying on it (ruling on CBP CROSS).
Key passages, quoted from the ruling
- In accordance with Note 3 to Section XVI, the applicable subheading will be 8413.60.0030, Harmonized Tariff Schedule of the United States (HTSUS), which provides for Pumps for liquids, whether or not fitted with a measuring device; liquid elevators; part thereof: Other rotary positive displacement pumps: Hydraulic fluid power pumps: Gear type.
Ruling text
In your letter dated February 24, 2025, you requested a tariff classification ruling. The merchandise at issue is referred to as a Hydraulic Power Unit, model number T94C405C93F0-01. The unit primarily consists of a gear pump, a manifold assembly, a bell housing, a relief valve, a suction elbow, a pressure hose, and a motor mounted to a steel reservoir. Together, the components of the unit perform a principal function, i.e., to pump pressurized hydraulic fluid to a connected application.
The power unit can be used to power a variety of machines, e.g., scissor lifts, presses, vehicle hoists, and a myriad of hydraulically operated machines used in manufacturing processes.
In accordance with Note 3 to Section XVI, the applicable subheading will be 8413.60.0030, Harmonized Tariff Schedule of the United States (HTSUS), which provides for Pumps for liquids, whether or not fitted with a measuring device; liquid elevators; part thereof: Other rotary positive displacement pumps: Hydraulic fluid power pumps: Gear type. The general rate of duty is free.
You inquire about subheading 9802.00.80, HTSUS, which provides a partial duty exemption for: articles assembled abroad in whole or in part of fabricated components, the product of the United States, which (a) were exported in condition ready for assembly without further fabrication, (b) have not lost their physical identity in such articles by change in form, shape, or otherwise, and (c) have not been advanced in value or improved in condition abroad except by being assembled and except by operations incidental to the assembly process, such as cleaning, lubricating, and painting.
All three requirements of subheading 9802.00.80, HTSUS, must be satisfied before a component may receive a duty allowance. An article entered under this tariff provision is subject to duty upon the full cost or value of the imported assembled article, less the cost or value of the U.S. components assembled therein, upon compliance with the documentary requirements of section 10.24, Customs Regulations (19 CFR 10.24).
In your letter, you state the reservoir, certain gaskets, bell housing, adapter, manifold, manifold adapter, ? valves, and the labels are of U.S. origin and exported to Canada in a condition that is ready for final assembly. The U.S. components are imported into Canada without further fabrication.
Upon compliance with the documentary requirements of 19 CFR 10.24, these U.S. origin components meet all three requirements of subheading 9802.00.80, HTSUS and are entitled to the duty exemption under subheading 9802.00.80, HTSUS.
Products of Canada as provided by heading 9903.01.10 in Section XXII, Chapter 99, Subchapter III, U.S. Note 2(j), HTSUS, other than products classifiable under headings 9903.01.11, 9903.01.12, 9903.01.13, 9903.01.14, and 9903.01.15, HTSUS, will be subject to an additional 25 percent ad valorem rate of duty. At the time of entry, you must report the applicable Chapter 99 heading, i.e. 9903.01.10, in addition to subheading 8413.60.0030, HTSUS, listed above.
The text above is an excerpt. The official ruling, with its letterhead, signature and any attachments, is on CBP CROSS (N346222).