The tariff classification of a silicone plastic plug and seal from Mexico.
No revocation or modification of this ruling appears in the Customs Bulletin issues read here (Nov 6, 2024 through Nov 18, 2026), where CBP publishes most such actions. That is not confirmation that the ruling is still in effect. Confirm its status with CBP before relying on it (ruling on CBP CROSS).
Key passages, quoted from the ruling
- The applicable subheading for the “6P Interface Seal,” internal part number 812018, will be 3926.90.4590, HTSUS, which provides for “[o]ther articles of plastics and articles of other materials of headings 3901 to 3914: [o]ther: [g]askets, washers and other seals: [o]ther.” The column one, general rate of duty is 3.5 percent ad valorem.
Ruling text
In your letter dated May 20, 2025, you requested a tariff classification ruling. Images were provided in lieu of samples. This request consists of two products for consideration. The first item is described as a “Mini UMNL Cavity Plug Seal,” internal part number 117001. It is a small plug designed to block off an empty cavity in a Universal MATE-N-LOK (UMNL) electrical connector where a wire is not being used. It measures 4.1 millimeters in diameter at its widest point and is 7 millimeters long.
The second item is described as a “6P Interface Seal,” internal part number 812018. It is a component used in six position (6P) electrical connectors and is specifically designed to prevent moisture, dust, and other contaminants from entering the connection area. It measures 0.8 inches by 0.55 inches. In your submission you describe these products as being made from silicone rubber and propose they be classified under heading 4016 as other articles of rubber.
Note 4 to Chapter 40, Harmonized Tariff Schedule of the United States (HTSUS), describes synthetic rubber as applying to unsaturated synthetic substances which can be irreversibly transformed by vulcanization with sulfur into non-thermoplastic substances which, at a temperature between 18 and 29 degrees Centigrade, will not break on being extended to three times their original length and will return, after being extended to twice their original length, within a period of 5 minutes, to a length not greater than 1-1/2 times their original length.
Silicone is not unsaturated, and thus, is not cross-linkable with sulfur. Therefore, silicone is not considered to be rubber for tariff classification purposes and will be classified under chapter 39 as a plastic.
The applicable subheading for the “6P Interface Seal,” internal part number 812018, will be 3926.90.4590, HTSUS, which provides for “[o]ther articles of plastics and articles of other materials of headings 3901 to 3914: [o]ther: [g]askets, washers and other seals: [o]ther.” The column one, general rate of duty is 3.5 percent ad valorem.
As the “Mini UMNL Cavity Plug Seal,” internal part number 117001, would be considered an article of plastic, and as it is not more specifically provided for elsewhere, the applicable subheading will be 3926.90.9989, HTSUS, which provides for “[o]ther articles of plastics and articles of other materials of headings 3901 to 3914: [o]ther: [o]ther: [o]ther.” The column one, general rate of duty is 5.3 percent ad valorem.
Products of Mexico as provided by heading 9903.01.01 in Section XXII, Chapter 99, Subchapter III, U.S. Note 2(a), HTSUS, other than products classifiable under headings 9903.01.02, 9903.01.03, 9903.01.04, and 9903.01.05, HTSUS, will be subject to an additional 25 percent ad valorem rate of duty. At the time of entry, you must report the applicable Chapter 99 heading, i.e., 9903.01.01, in addition to subheadings 3926.90.4590 and 3926.90.9989, HTSUS, listed above.
The text above is an excerpt. The official ruling, with its letterhead, signature and any attachments, is on CBP CROSS (N349241).