The tariff classification of landing gear parts for the front of a fifth wheel and commercial trailer from Canada
No revocation or modification of this ruling appears in the Customs Bulletin issues read here (Nov 6, 2024 through Nov 18, 2026), where CBP publishes most such actions. That is not confirmation that the ruling is still in effect. Confirm its status with CBP before relying on it (ruling on CBP CROSS).
Key passages, quoted from the ruling
- The applicable subheading for landing gear parts for the front of a fifth wheel and commercial trailer will be 8716.90.5060, HTSUS, which provides for “Trailers and semi-trailers; other vehicles, not mechanically propelled; and parts thereof: Parts: Other: Other.” The rate of duty will be 3.1 percent ad valorem.
Ruling text
In your letter dated July 18, 2025, you requested a tariff classification determination on behalf of your client, Nova Steel Inc., located in La Salle, Canada. Several pictures, illustrations, and exhibits were provided with your request. The articles under consideration have been identified as the driven legs, specialized landing gear parts, used on trailers classified in heading 8716 of the Harmonized Tariff Schedule of the United States (HTSUS).
The driven leg landing gear parts are square, hot rolled, pickled and oiled steel tubes. You state that, in Canada, the driven leg landing gear parts are cut to-length, manufactured to specific customer tolerances, and laser-cut with holes. You further state that these parts do not undergo any further processing in the United States, thereby, making the driven leg landing gear parts ready for assembly upon importation and use in the trailer chassis.
The landing gears are permanently attached to the underside of trailers. Landing gears are used to lift and stabilize a vehicular trailer so that it may be disengaged from the fifth wheel of a tractor. The driven legs are integral parts of the landing gear legs, forming the structural integrity of the legs of the gears, without which the landing gear could not function. Landing gears are comprised of both a left and right leg and are typically installed at the front of a vehicular trailer.
The left and right legs of the landing gear require five (5) separate sub-assemblies that are required for the landing gear’s functionality: the driving leg assembly; driven leg assembly; foot assembly; crank assembly and connection shaft. You indicate these parts will be used in your client’s landing gear product line, listed below. 1. A400 - Static Load Capacity 160,000 lbs. 2. A440 - Static Load Capacity 170,000 lbs. 3. A450 - Static Load Capacity 170,000 lbs. 4. H450 - Static Load Capacity 200,000 lbs. 5.
UL500 - Static Load Capacity 160,000 lbs. 6. AX100 - Static Load Capacity 160,000 lbs. The applicable subheading for landing gear parts for the front of a fifth wheel and commercial trailer will be 8716.90.5060, HTSUS, which provides for “Trailers and semi-trailers; other vehicles, not mechanically propelled; and parts thereof: Parts: Other: Other.” The rate of duty will be 3.1 percent ad valorem. Effective May 3, 2025, Presidential proclamation 10908 imposed additional tariffs on certain automobile parts.
Additional duties on automobile parts of 25 percent are reflected in Chapter 99, heading 9903.94.05, as provided in subdivision (g) of U.S. note 33 to this subchapter. At the time of entry, you must report the Chapter 99 heading applicable to your product classification, i.e. 9903.94.05, in addition to subheading 8716.90.5060, HTSUS, listed above.
Articles that are eligible for special tariff treatment under the United States-Mexico-Canada Agreement (USMCA), other than automobile knock-down kits or parts compilations; or are not parts of passenger vehicles (sedans, sport utility vehicles, crossover vehicles, minivans or cargo vans) and light trucks, will not be subject to the additional ad valorem duties provided for in heading 9903.94.05.
The text above is an excerpt. The official ruling, with its letterhead, signature and any attachments, is on CBP CROSS (N351496).