The country of origin and eligibility of the United States-Mexico-Canada Agreement (USMCA) of a Walk-Behind Lawn Mower
No revocation or modification of this ruling appears in the Customs Bulletin issues read here (Nov 6, 2024 through Nov 18, 2026), where CBP publishes most such actions. That is not confirmation that the ruling is still in effect. Confirm its status with CBP before relying on it (ruling on CBP CROSS).
Key passages, quoted from the ruling
- The walk-behind lawn mower is classified under subheading 8433.11.0050, HTSUS.
- Therefore, the tariff shift is met and the country of origin of the walk-behind lawn mower will be Mexico for marking purposes.
Ruling text
This is in response to your letter dated September 22, 2025, on behalf of Daye North America, Inc. (Daye), requesting a ruling on the country of origin and eligibility of the United States-Mexico-Canada Agreement (USMCA) of a walk-behind lawn mower. A comprehensive bill of materials and descriptions of the components of the lawn mower were included with your submission. You have stated that Daye plans to manufacture in Mexico a walk-behind lawn mower with components from China, Mexico and the United States.
In Mexico, the mower deck assembly will be manufactured via a stamping process using Mexican steel. After stamping, the steel components will be powder coated. Additionally in Mexico, Daye will manufacture the grass outlet bracket, rear cover, front mask, front mask base, side discharge cover, wheel assemblies and their covers, and side discharge protection cover. These parts will be produced by injection molding processes that utilize Chinese origin plastic. Daye will also a purchase a Mexican origin gearbox.
The lawn mower blades will be imported from China, along with the front and rear axle assemblies, handrail assembly, grass collection bag, flame-out cable assembly, brackets, nuts, bolts, screws, washers, clamps, bushings, springs, and gaskets. The mower’s gasoline-powered engine will be of U.S. origin and have a maximum power output of 3.23 kW. These components, along with the Mexican components, will be assembled into the finished walk-behind lawn mower in Mexico.
You have stated that this final assembly, inspection, and testing of all the components will also require manual labor. USMCA: The USMCA was signed by the Governments of the United States, Mexico, and Canada on November 30, 2018. The USMCA was approved by the U.S. Congress with the enactment on January 29, 2020, of the USMCA Implementation Act, Pub. L. 116-113, 134 Stat. 11, 14 (19 U.S.C. § 4511(a)). General Note (GN) 11 of the Harmonized Tariff Schedule of the United States (HTSUS) implements the USMCA.
GN 11(b) sets forth the criteria for determining whether a good is an originating good for purposes of the USMCA.
GN 11(b) states: For the purposes of this note, a good imported into the customs territory of the United States from the territory of a USMCA country, as defined in subdivision (l) of this note, is eligible for the preferential tariff treatment provided for in the applicable subheading and quantitative limitations set forth in the tariff schedule as a “good originating in the territory of a USMCA country” only if- (i) the good is a good wholly obtained or produced entirely in the territory of one or more USMCA countries; (ii) the good is a good produced entirely in the territory of one or more USMCA countries, exclusively from originating materials; (iii) the good is a good produced entirely in the territory of one or more USMCA countries using non-originating materials, if the good satisfies all applicable requirements set forth in this note (including the provisions of subdivision (o)); The subject walk-behind lawn mower contains non-originating materials and is not considered a good wholly obtained or produced entirely in a USMCA country under GN 11(b)(i).
The text above is an excerpt. The official ruling, with its letterhead, signature and any attachments, is on CBP CROSS (N354024).