The tariff classification of gaskets assemblies for heavy-duty diesel trucks from Mexico
No revocation or modification of this ruling appears in the Customs Bulletin issues read here (Nov 6, 2024 through Nov 18, 2026), where CBP publishes most such actions. That is not confirmation that the ruling is still in effect. Confirm its status with CBP before relying on it (ruling on CBP CROSS).
Key passages, quoted from the ruling
- The applicable subheading for the steel/elastomer gaskets will be 8409.99.9190, HTSUS, which provides for “Parts suitable for use solely or principally with the engines of heading 8407 or 8408: Other: Other: To be installed in vehicles of…heading 8702, 8703 or 8704: Other.” The general rate of duty will be 2.5% ad valorem.
Ruling text
In your letter dated October 2, 2025, you requested a tariff classification ruling. The items under consideration have been identified as a family of gasket assemblies specially designed for use in heavy-duty diesel truck engines. You state that each gasket consists of a stamped substrate of ASTM A463 aluminized steel sheeting that is permanently overmolded with an elastomer sealing bead.
During the molding process, an adhesive system will be employed so that the elastomer bead will be permanently bonded to the steel stamping, creating an inseparable composite article. The steel substrate provides the structural form and dimensional stability, while the elastomer bead enhances sealing performance. A representative article includes: Steel stamping thickness: 0.76 mm nominal Elastomer bead thickness: 1.14 mm nominal Elastomer type: fluorocarbon rubber (FKM) Steel weight: 0.153 kg (0.336 lbs.)
Rubber weight: 0.0072 kg (0.0158 lbs.) You state that the steel substrate accounts for approximately 95% of the total article weight.
The family of gaskets shares this same construction and geometry, with the following dimensional and material variations depending on engine model and sealing application: Steel stamping thickness range: 0.76 mm to 1.52 mm nominal Elastomer bead thickness range: 1.09 mm to 2.4 mm nominal Elastomer types: fluorocarbon, hydrogenated nitrile (HNBR), AFLAS® (tetrafluoroethylene-propylene rubber), or silicone (VMQ) You state that all gaskets in the family perform the same function: providing a durable, fluid-tight seal between mating engine components (e.g., valve cover, oil cooler, thermostat housing, flywheel housing, fuel pump, or timing cover) in heavy-duty diesel engines You suggest classification of the gasket assemblies in subheading 7326.90, Harmonized Tariff Schedule of the United States (HTSUS), which provides for “Other articles of iron or steel: Other.” Heading 7326, HTSUS, is a residual or basket provision which covers a wide range of iron or steel articles that are not more specifically provided for elsewhere in the HTSUS.
The ENs to heading 7326 state that “This heading covers all iron or steel articles obtained by forging or punching, by cutting or stamping or by other processes such as folding, assembling, welding, turning, milling or perforating other than articles included in the preceding headings of this Chapter or covered by Note 1 to Section XV or included in Chapter 82 or 83 or more specifically covered elsewhere in the Nomenclature.” An article of iron or steel can be classified in heading 7326 if it is determined that the item is not more specifically provided for in any other heading of the tariff.
Noting the gasket assemblies are more specifically provided for elsewhere, they cannot be classified in heading 7326, HTSUS. The applicable subheading for the steel/elastomer gaskets will be 8409.99.9190, HTSUS, which provides for “Parts suitable for use solely or principally with the engines of heading 8407 or 8408: Other: Other: To be installed in vehicles of…heading 8702, 8703 or 8704: Other.” The general rate of duty will be 2.5% ad valorem.
The text above is an excerpt. The official ruling, with its letterhead, signature and any attachments, is on CBP CROSS (N354570).