The eligibility of the United States-Mexico-Canada Agreement (USMCA) of a heat sink assembly from Canada
No revocation or modification of this ruling appears in the Customs Bulletin issues read here (Nov 6, 2024 through Nov 18, 2026), where CBP publishes most such actions. That is not confirmation that the ruling is still in effect. Confirm its status with CBP before relying on it (ruling on CBP CROSS).
Key passages, quoted from the ruling
- The only non-originating article in the assembly is the aluminum heat sink casting from China, which is classified in heading 7619, HTSUS.
- As previously noted, the heat sink assembly is classified under subheading 9027.90.5650, HTSUS.
- The heat sink would be classified in Chapter 76 while the finished heat sink assembly is classified in subheading 9027.90, HTSUS.
Ruling text
In your letter dated October 8, 2025, on behalf of your client, Visby Medical, you requested a binding ruling on the eligibility of a heat sink assembly under the United States-Mexico-Canada Agreement (USMCA). The item under consideration is described as a heat sink assembly that is incorporated into the Visby Respiratory Health Point of Care Test and Visby Medical Sexual Health Test.
The heat sink assembly is a specially designed part of the completed medical diagnostic units whose main purpose is to dissipate heat from electronic components, preventing them from overheating, and ensuring reliable operation. The heat sink accomplishes this with its uniquely shaped design by absorbing heat from the components before transferring the heat to the surrounding environment.
The complete heat sink assembly includes the Chinese origin aluminum heat sink and several United States origin components that includes two plastic elbows, a 4-up coupler, tubing, and adhesive.
In New York Ruling N352482 (dated September 3, 2025), CBP ruled that according to Chapter 90 Note 2(b), the heat sink assembly was a part of the Visby Respiratory Health Point of Care Test and Visby Medical Sexual Health Test, and classified the complete article in subheading 9027.90.5650, Harmonized Tariff Schedule of the United States (HTSUS). The only non-originating article in the assembly is the aluminum heat sink casting from China, which is classified in heading 7619, HTSUS.
The USMCA was signed by the governments of the United States, Mexico, and Canada on November 30, 2018. The USMCA was approved by the U.S. Congress with the enactment on January 29, 2020, of the USMCA Implementation Act, Pub. L. 116-113, 134 Stat. 11, 14 (19 U.S.C. § 4511(a)). General Note (GN) 11 of the HTSUS implements the USMCA. GN 11(b) sets forth the criteria for determining whether a good is an originating good for purposes of the USMCA.
GN 11(b) states: For the purposes of this note, a good imported into the customs territory of the United States from the territory of a USMCA country, as defined in subdivision (l) of this note, is eligible for the preferential tariff treatment provided for in the applicable subheading and quantitative limitations set forth in the tariff schedule as a “good originating in the territory of a USMCA country” only if- (i) the good is a good wholly obtained or produced entirely in the territory of one or more USMCA countries; (ii) the good is a good produced entirely in the territory of one or more USMCA countries, exclusively from originating materials; (iii) the good is a good produced entirely in the territory of one or more USMCA countries using non-originating materials, if the good satisfies all applicable requirements set forth in this note (including the provisions of subdivision (o)).
Since the heat sink assembly contains non-originating articles, they are not considered a good wholly obtained or produced entirely in a USMCA country under GN 11(b)(i), nor are the products produced exclusively from originating materials per GN 11(b)(ii). Thus, we must determine whether the product qualifies under GN 11(b)(iii).
The text above is an excerpt. The official ruling, with its letterhead, signature and any attachments, is on CBP CROSS (N354772).