The country of origin of brake hubs
No Headquarters ruling in this index revokes or modifies this ruling. That is not confirmation that it is still in effect: this index does not hold every Headquarters ruling. Confirm its current status with CBP before relying on it (ruling on CBP CROSS). Text last read from CBP on Nov 21, 2026.
Key passages, quoted from the ruling
- None of the separate components of the hubs is classified in subheading 8708.99, HTSUS, or any of the listed excepted subheadings.
- As a result, it is the opinion of this office that the country of origin of the Front Hub-drum Assembly (high-runner), PN MHP-A001ALP; Front Assembly, PN 243076, and Rear Assembly, PN 343076 will be China for purposes of applying trade remedies under Section 301, as amended, from China, and additional duties.
Ruling text
In your letter, dated August 17, 2026, you requested a country of origin ruling on brake hubs for marking purposes; for purposes of applying trade remedies under Section 301, as amended, from China, and additional duties; and applicability of the United States-Mexico-Canada Agreement (USMCA). The articles under consideration are described as a Front Hub-drum Assembly (high-runner), Part Number (PN) MHP-A001ALP; Front Assembly, PN 243076, and Rear Assembly, PN 343076.
Each assembly consists of a hub, wheel stud, bearing cup, and tone ring. Additionally, PN MHP-A001ALP contains an oil port plug; PN 243076 has a front brake drum, nut, and an outer bearing cup; and PN 343076 has a rear brake drum, flange stud, nut, and an outer bearing cup. The articles are designed to be used with heavy-duty trucks as original equipment manufacturers (OEM) goods. You state that the hubs for each assembly are imported to Mexico from China in a rough, unfinished state.
In Mexico, the hubs undergo computer numerical control (CNC) turning, hole drilling, thread tapping, and countersinking. Then, the bearing cups from China and Thailand, tone ring, and studs are hydraulically pressed into the holes. Finally, the brake drums of Mexican origin are mechanically coupled with the hubs.
Marking: Section 304 of the Tariff Act of 1930, as amended (19 U.S.C. 1304), provides that unless excepted, every article of foreign origin imported into the United States shall be marked in a conspicuous place as legibly, indelibly, and permanently as the nature of the article (or its container) will permit, in such a manner as to indicate to the ultimate purchaser in the United States, the English name of the country of origin of the article.
Congressional intent in enacting 19 U.S.C. 1304 was “that the ultimate purchaser should be able to know by an inspection of the marking on the imported goods the country of which the goods is the product. The evident purpose is to mark the goods so that at the time of purchase the ultimate purchaser may, by knowing where the goods were produced, be able to buy or refuse to buy them, if such marking should influence his will.” See United States v. Friedlaender & Co., 27 C.C.P.A. 297, 302 (1940).
Section 134.1(b), CBP Regulations (19 CFR 134.1(b)), defines “country of origin” as the country of manufacture, production, or growth of any article of foreign origin entering the United States. Further work or material added to an article in another country must effect a substantial transformation in order to render such other country the “country of origin” within the meaning of the marking laws and regulations.
Pursuant to section 102.0, interim regulations, related to the marking rules, tariff-rate quotas, and other USMCA provisions, published in the Federal Register on July 6, 2021 (86 FR 35566), the rules set forth in sections 102.1 through 102.18 and 102.20 determine the country of origin for marking purposes with respect to goods imported from Canada and Mexico.
The text above is an excerpt. The official ruling, with its letterhead, signature and any attachments, is on CBP CROSS (N364352).