The tariff classification of multilayer wood panels from Mexico
No revocation or modification of this ruling appears in the Customs Bulletin issues read here (Nov 6, 2024 through Nov 18, 2026), where CBP publishes most such actions. That is not confirmation that the ruling is still in effect. Confirm its status with CBP before relying on it (ruling on CBP CROSS).
Key passages, quoted from the ruling
- The applicable subheading for the three-ply wood panels with outer plies of nonconiferous wood and a fiberboard core will be 4412.92.5215, Harmonized Tariff Schedule of the United States (HTSUS), HTSUS, which provides for Plywood, veneered panels and similar laminated wood: Other: Other, with at least one outer ply of nonconiferous wood: Other: Other: Other.
Ruling text
In your letter dated August 6, 2025, you requested a tariff classification ruling on multilayer wood panels. Product information was submitted for review. The product under consideration is a three-ply wood panel. The panel is constructed of a face and back ply of wood veneer that measures approximately 0.5mm to 0.6mm in thickness, and a core of medium density fiberboard (MDF) that ranges from 5.2mm to 19mm in thickness.
The panels measure approximately 4’ wide by 8’ long and in thickness ranging from 6.2mm to 20.2mm. You state the face ply may consist of one of several non-coniferous woods including maple (Acer spp.), red oak (Quercus rubra), white oak (Quercus alba), alder (Alnus spp.), beech (Fagus spp.), ash (Fraxinus spp.), birch (Betula spp.), or walnut (Juglans spp. ). The back ply will be the same species as the face ply but of a lower grade.
You state the panels have a straight-cut edge with an unfinished surface where the grain remains visible. You indicate these panels are intended for fabrication into furniture, cabinetry, fixtures, and architectural millwork. In understanding the language of the Harmonized Tariff Schedule of the United States (HTSUS), the Explanatory Notes to the Harmonized System (ENs) may be utilized.
The ENs, although not dispositive nor legally binding, provide a commentary on the scope of each heading of the HTSUS, and are the official interpretation of the Harmonized System at the international level. See T.D. 89-80, 54 Fed. Reg. 35127, 35128 (August 23, 1989). You question whether these wood panels are classifiable as veneered panels of heading 4412, HTSUS, or as medium density fiberboard (MDF) of heading 4411, HTSUS.
The Explanatory Notes (ENs) to the Harmonized System for heading 4412 specifically define “veneered panels” as “panels consisting of a thin veneer of wood affixed to a base, usually of inferior wood, by gluing under pressure.” The instant wood panel meets this description, as the veneer gives the panel its essential character, and the veneer is affixed to a base of MDF. Veneered panels are specifically provided for in the language of heading 4412, Harmonized Tariff Schedule of the United States (HTSUS).
While fiberboard products are classified in heading 4411, HTSUS, the Explanatory Notes (ENs) to heading 4411 specifically exclude products covered in wood veneer: “This heading does not cover (b) Laminated wood with a core consisting of fibreboard (heading 44.12). Therefore, the instant panel with outer plies of nonconiferous wood and a fiberboard core is precluded from heading 4411, HTSUS.
The applicable subheading for the three-ply wood panels with outer plies of nonconiferous wood and a fiberboard core will be 4412.92.5215, Harmonized Tariff Schedule of the United States (HTSUS), HTSUS, which provides for Plywood, veneered panels and similar laminated wood: Other: Other, with at least one outer ply of nonconiferous wood: Other: Other: Other. The rate of duty will be free. Products of Mexico as provided by heading 9903.01.01 in Section XXII, Chapter 99, Subchapter III, U.S.
The text above is an excerpt. The official ruling, with its letterhead, signature and any attachments, is on CBP CROSS (N352099).